X freq Y ampli

来源: Freesound 前往原页面 查看译文
作者:gis_sweden
许可:CC0 公众共享许可协议  
描述:Yep this is a crazy sound. What have I done...I have build a Nonlinearcircuits Sloth LFO.https://www.modulargrid.net/e/nonlinearcircuitssloth4hpEDITED INFO:I have built the regular version. The Sloth has two outputs X and Y. I connected X to control frequency on one oscillator and Y to control amplitude on another oscillator.Frequency experiment on left channel.Amplitude experiment on the right.The file starts as the amplitude is 0. Next time the amplitude is 0 (almost) is at about 48 sec. Then 48 sec later, at 1:37 the amplitude is 0 again. The two cycles are not identical. The tones are harder to analyze...X and Y outputs. I guess those corresponds to X and Y in a coordinate system. You can find video clips watching the Sloth “drawing” butterfly wings. For example:https://www.youtube.com/watch?v0KU6NPz1S4gAnd maybe check this:https://www.youtube.com/watch?vocChcM5oxp8http://nonlinearcircuits.blogspot.se/2014/09/slothchaos.htmlThis later link is the developers page.The constructor (Andrew) of this module says that my version completes “1 cycle every 15 seconds”. What does that mean? Is one cycle one lap in the butterfly pattern? Will the pattern repeat itself? Yep, I’m going to ask him… EDIT:Andrew answers my questions: “It is a very approximate description of the frequency, cycle is not the proper term to use....nor is frequency really, but they are descriptions that people can relate to easily.Depending upon the pot settings and whatever other initial conditions that happen to be in place, the signal may traverse the typical double strange attractor path. It may stay in one attractor for several loops before crossing over to the other one.The pattern will never repeats itself, it might come close but won't do it.”My question: So, one “loop” is one cycle?Andrew answers: Typically it takes approx 15 seconds to make a rough figure 8, but depending upon the pot and other factors, it may take longer, much longer, sometimes it even pauses whilst deciding which way to go next.
标签: test synth DIY modular chaos LFO
音频格式wav
声音时长01:57
文件大小19.7 MB
比特率1410 kbps
采样率44100 Hz
位深度16 bit
声道立体声
音频蛋下载 推荐

◦  支持一键下载
◦  智能提速线路
◦  队列批量下载
◦  免费跨站下载

  加入任务队列
原站点下载 备用

◦  账户登录下载
◦  普通站点线路
◦  单个文件下载
◦  免费站内下载

  前往声音页面

———— 类似的声音 ————

来源Freesound
描述:由混沌模块控制的模块化合成器哔哔声和臃肿。这会让它变得更好吗?不!
来源Freesound
描述:两个噪音发生器发出的噪音。用连接在iPhone上的迷你胶囊麦克风录制的声音。
来源Freesound
描述:两个噪音发生器发出的噪音。用连接在iPhone上的迷你胶囊麦克风录制的声音。
来源Freesound
描述:不确定性驱动补丁的来源
来源Freesound
描述:仅使用一个vco击败合成器上的补丁,polivoks过滤器有时会产生共鸣。
来源Freesound
描述:Doepfer Synth Chaos
by gis_sweden
来源Freesound
描述:另一个Sloth LFO测试。我希望看到 预计会看到 周期重复。我不。我有X控制频率和Y控制滤波器。这个录音是5分钟所以应该有一些重复......这是一个常规的懒惰...我看到48秒的循环,但它们不一样。冷。混沌。
来源Freesound
描述:有点敢与用户gis_sweden一起运行。挑战是创建一个声音,其中2个振荡器互相交叉调制.gis_sweden将使用他的模块化合成器。我将使用我的虚拟模块合成器Kamiooka。你可以在这里听到gis_sweden的声音:http://freesound.org/people/gis_sweden/sounds/346401/ 如果将显示模式更改为光谱,我的声音看起来很有趣。 我使用的参数:2个sin振荡器彼此交叉调制(FM)交叉调制量在120bpm的20巴期间从0到最大(100%)线性上升。用Ableton LiveSound中的Kamiooka处理,在Audacity中转换为单声道。没有效果或处理。
来源Freesound
描述:摘录录音
来源Freesound
描述:模块上的嘈杂序列很短
来源Freesound
描述:录音短
by vladj
来源Freesound
描述:小diy合成器上的图案
by vladj
来源Freesound
描述:像图案一样的脏字符串。
来源Freesound
描述:短脏序列
来源Freesound
描述:模式与奇怪的时间和suboctave低音